| |
 Forum: German / Deutsch
Topic: Update HMT370 funktioniert nicht
-
NorbertA
- Status: Offline
- Messages: 7
- Registration date:
June 28, 2015
Quote:
The icon with the L is not really important. It only shows if the listenlive server (that serves the station lists and also runs this website) has been reached.
If it did, it will be able to pull updated station lists. If it failed it will not pull the updates but keep on using the lists that are already on the device.
As stations are not changing that rappidly, it will not be a problem if you did not pull updates for some time.. - I understand, but my german station list was just 1177 entries and didn't change The other icon is more important, is this shows if there was a wifi or wired lan connection.
On the HMT370 both wifi and wired should work but of course you need to select the right connection type and its related settings (like using a static or dynamic IP address)
Wired works faster and more stable than wifi but most people dont have wires to every corner of the house  I can see the disconncted icon the wiFi Icon, and the connected with DHCP correctly Icon (never saw the green one) in turns
When using Wifi, WPA/WPA2 with a dynamic IP address (usually means IP address provided by your router) works best.
If it constantly re-connects it might be possible that it switches back and forth between two wifi networks. Possibly because the strength of the two networks is more or less the same and fluctuating a bit.
In this case do a factory reset and answer yes to the question if it should reset all network settings.
- I did that and connected only to one WLAN It is also possible that the wifi channel your router/wifi access point is set for, is changing too fast for the device to keep up with.
This happened before.
Some routers are checking if another nearby signal is using the same wifi channel, if it does, the router will select a new channel.
That sounds of course great.. but imagine there are two or even more routers that are doing the same thing. They will keep on forcing eachother to change the wifi channel.
Most modern laptops are fast enough to keep up with such changes, your HMT might not.. it was reported before that disabling "dynamic wifi channel selection" solved some issues. - I already fixed the channel of my WLan router, this is not the reason. I thonk it really s a WiFi Hardware reason and give in
~William
|
-
penbex
- Status: Offline
- Messages: 2421
- Registration date:
May 21, 2009
The icon with the L is not really important. It only shows if the listenlive server (that serves the station lists and also runs this website) has been reached.
If it did, it will be able to pull updated station lists. If it failed it will not pull the updates but keep on using the lists that are already on the device.
As stations are not changing that rappidly, it will not be a problem if you did not pull updates for some time.. The other icon is more important, is this shows if there was a wifi or wired lan connection.
On the HMT370 both wifi and wired should work but of course you need to select the right connection type and its related settings (like using a static or dynamic IP address)
Wired works faster and more stable than wifi but most people dont have wires to every corner of the house When using Wifi, WPA/WPA2 with a dynamic IP address (usually means IP address provided by your router) works best.
If it constantly re-connects it might be possible that it switches back and forth between two wifi networks. Possibly because the strength of the two networks is more or less the same and fluctuating a bit.
In this case do a factory reset and answer yes to the question if it should reset all network settings.
It is also possible that the wifi channel your router/wifi access point is set for, is changing too fast for the device to keep up with.
This happened before.
Some routers are checking if another nearby signal is using the same wifi channel, if it does, the router will select a new channel.
That sounds of course great.. but imagine there are two or even more routers that are doing the same thing. They will keep on forcing eachother to change the wifi channel.
Most modern laptops are fast enough to keep up with such changes, your HMT might not.. it was reported before that disabling "dynamic wifi channel selection" solved some issues. ~William
-
NorbertA
- Status: Offline
- Messages: 7
- Registration date:
June 28, 2015
I'm not sure that it is a WiFi Issue. Butt the status icon(s) in the upper right corner show a connection, after short time there is no connection, then there is a Connection again after some seconds. And so on. The Internet Radio is playing ok for some seconds then it pauses then plays again for some seconds and then it stops on a screnn so that I have to press a key. I can see news stations, but if I select one, there are no news to see. Can I see somewherehow strong (good) the WiFi signal is ? I can play Internet Radio on my Laptop right beside the HMT 370.
-
penbex
- Status: Offline
- Messages: 2421
- Registration date:
May 21, 2009
Wifi should work without any issues.
Note that there is no difference between the Original firmware and the listenlive firmware in terms of wlan drivers.
Are you sure that it is a wifi issue? how about other functions, like the news page..(to test wifi)
-
NorbertA
- Status: Offline
- Messages: 7
- Registration date:
June 28, 2015
Hi, also das mit den Favoriten funktioniert jetzt (Irgendwie ging die Einstellung welches Gerät ich habe verloren, und dann gehen die Favoriten nicht). Aber meine WLan Verbindung ist immer noch ein 'Blinker' und ich kann mal gerade 10 Sek SWR3 hören, dann ist Schluß.
Hat noch jemand eine Idee? Ist es wohlmöglich wirklich ein HW Problem? Ist da was bekannt, dass das HMT370 ein 'wackeliges' WiFi Modul hat?
LG Norbert
-
NorbertA
- Status: Offline
- Messages: 7
- Registration date:
June 28, 2015
Ok, now I do have the 1.52 firmware on my HMT370. But I cant see all German Radio Stations (the List says it has got 1177 entries but there are 2277 in the list here). And my favorite Station (SWR3) is not in the List as it stops at L. Also the WLAN is very unstable although I had a good connect with the orginal firmware before. I can't see my favorites (my account is not in the list of the LL accounts). Do I have to activate something? (I've set up a PIN) I tried connecting with a cable but no success with the lists (radio stations, accounts). And I could hear a Radio Station. Also I've got favorites (from whomever) but not mine. Any help appreciated.
Nochmal auf deutsch schließlich ist das ja die deutsche Sektion: Ich habe nun erfolgreich die firmware 1.52 auf mein HMT 370 geschafft. Aber die WLAN Verbindung ist nicht zuverlässig, obwohl sie das mit der original Firmware (einigermaßen) war. Handys und Laptop verbinden an dieser Stelle sehr gut mit dem WALN. Meine Radiosenderliste (Deutschland) geht nur bis L und ich bekomme meinen Lieblingssender SWR3 nicht (es sind nur 1177 Einträge statt 2277 hier vom Server). Um Favoriten zu laden kann ich meinen Account nicht einstellen - er fehlt in der Liste der accounts - die PIN habe ich gesetzt. Ich habe versucht, ob das Ganze mit einem LAN Kabel besser geht. Hat aber für die Listen nix geholfen. Seitdem sehe ich aber die Favoriten von irgendwem. Irgend jemand noch Ideen?
Danke im voraus Norbert
-
NorbertA
- Status: Offline
- Messages: 7
- Registration date:
June 28, 2015
Hi, that really did the Job. I 'borrowed' a SD Card from my daughters camera (didn't even have to erase or format it) and the update worked. Thank you for your help.
Kind regards Norbert
-
penbex
- Status: Offline
- Messages: 2421
- Registration date:
May 21, 2009
Hi, Make sure you use a regular SD card.. max. 2 Gb of size. (Check old phones/camera's etc. for an older card)
It should NOT be an SDHC, SD micro in adapter etc.
~William (Last Edited by penbex on June 29, 2015, 6:55 pm)
-
NorbertA
- Status: Offline
- Messages: 7
- Registration date:
June 28, 2015
Hallo, ich habe versucht die ll Software auf mein HMT370 zu spielen. Der Updater ist auch angekommen (per SD Karte). Die Firmare (1.52) wurde aber zunächst nicht erkannt. Nach neu Formatieren der Karte wurde das Update zwar erkannt, aber beim Einspielen bricht es mit einem 'verify' Fehler ab. Ich habe mehrfach versucht das Update neu auf die Karte zu spielen, aber es bricht immer mit dem gleichen Fehler ab. Ich habe auch versucht die Karte mit FAT32 zu formatieren. Macht auch keinen Unterschied. Es handelt sich um eine Micro SD Karte (2GB) in einem Adapter. Soll ich eine andere Karte besorgen? Habe ich mit einer 'kleineren' Karte bessere Chancen? Kann ich auf die original Software zurück? Nach dem Start mit gedrücktem OK Knopf findet er kein Recover File. Wie krieg ich das Ding wieder ans 'fliegen?
Grüße Norbert
|
|
